Page Comparison

• Pen is applied to the Wrong Place Horizontally.

  • This is viewed from the front of the mat.

• Tool line is applied too far Left:

  • Increase the Horizontal Adjustment.

• Tool line is applied too far Right:

  • Decrease the Horizontal Adjustment.

• See Pen Horizontal Adjustment for additional information.

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Tool line is applied too far Left, Increase the Horizontal Adjustment.

If the Tool line is applied too far Right, Decrease the Horizontal Adjustment.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Tool line is applied too far Up:

  • Decrease the Vertical Adjustment.

• Tool line is applied too far Down:

  • Increase the Vertical Adjustment.

• See Pen Vertical Adjustment for additional information.

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Tool line is applied too far Up, Decrease the Vertical Adjustment.

If the Tool line is applied too far Down, Increase the Vertical Adjustment.

• Pen is the Wrong Size.

  • This is viewed from the front of the mat.

• Opening is cut too Large:

  • Decrease the Opening Adjustment.

• Opening is cut too Small:

  • Increasethe Opening Adjustment.

• See Pen Opening Adjustment for additional information.

The Opening Adjustment controls the size of the Object cut or applied with non-blade cartridges.

If the Opening is cut too Large, Decrease the Opening Adjustment.

If the Opening is cut too Small, Increase the Opening Adjustmentthe Opening Adjustment.

• Pen is applied at the Wrong Depth.

• Non-Blade Tool is too Deep:

  • Decrease the Depth Setting.

• Non-Blade Tool is too Shallow:

  • Increase the Depth Setting.

• See Pen Depth Setting for additional information.

The Depth Setting controls the Blade Depth for the Non-Blade Tools in the Configurations.

If the Non-Blade Tool is too Deep, Decrease the Depth Setting.

If the Non-Blade Tool is too Shallow, Increase the Depth Setting.

• Pen Cartridge Tears the Mat.

• Non-Blade Tool is Tearing in the Corners of the segments:

  • Increase the Corner Pause. 

• Non-Blade Tool is Pausing Too Long in the Corners of the segments:

  • Decrease the Corner Pause. 

• See Pen Corner Pause for additional information.

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. 

• Pen Lines are drawn Too Long.

  • This is viewed from the front of the mat.

• Overshoot is too Long:

  Decrease the Overshoot.

• See Pen Overshoot for additional information.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot the Overshoot.

• Pen Lines are drawn Too Short.

  • This is viewed from the front of the mat.

• Overshoot is too Short:

  Increase the Overshoot.

• See Pen Overshoot for additional information.

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

• Set the Pen to Plunge Between Pen Line Segments.

1. The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

2. The Non-Blade Tool takes Too Long to apply, select Plunge.

3. See Plunge for additional information.

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

• How to Calibrate Different Pens.

1. Use the Install Pen utility to calibrate different pens.

2. See Install Pen for additional information.

The Pen Cartridge is used to draw onto the surface of the matboard on the CMC to create a design.

The Install Pen Utility is used to Calibrate each pen defined in the software.