Content Comparison

Note: Not all cartridges are available for all CMC models.

• The Other Cartridge Adjustments section contains additional configuration fields for V-Grooves and for the 

• To adjust, click

The Width Adjustment controls the Width of the V-Groove Lines.

If the V-Groove is cutting Too Thin, Increase the Width Adjustment.

If the V-Groove is cutting Too Wide, Decrease the Width Adjustment.

The Outside Rotation on Non-Oval V-Grooves controls for Swoops and Flares in the Outside Cut of the Non-Oval V-Grooves.

A Swoopin a Non-Oval V-Groove is where the corners Curve Inward toward the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Swoop, Decrease the Outside Rotation.

A Flare in a Non-Oval V-Groove is where the corners Curve Away from the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Outside Non-Oval V-Groove cuts with a Flare, Increase the Outside Rotation.

The Inside Rotation on Non-Oval V-Grooves controls for Swoops and Flares in the Inside Cut of the Non-Oval V-Grooves.

A Swoopin a Non-Oval V-Groove is where the corners Curve Inward toward the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Inside Non-Oval V-Groove cuts with a Swoop, Increase the Inside Rotation.

A Flare in a Non-Oval V-Groove is where the corners Curve Away from the opening on either the Outside or Inside Cut of the V-Groove.

The Rotation on Non-Oval V-Grooves controls for Swoopsor Flares on Non-Oval V-Grooves.

If the Inside Non-Oval V-Groove cuts with a Flare, Decrease the Inside Rotation.

The Outside Oval Rotation for V-Grooves controls for Feathers or Bumpson the Outside Cut of an Oval V-Groove.

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumpsor Featherson an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Feather, Increase the Outside Oval Rotation.

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumpsor Featherson an Oval V-Groove.

If the Outside Oval V-Groove cuts with a Bump, Decrease the Outside Oval Rotation.

The Inside Oval Rotation for V-Grooves controls for Feathers or Bumpson the Inside Cut of an Oval V-Groove.

A Feather in an Oval V-Groove is a Fringe of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumpsor Featherson an Oval V-Groove.

If the Inside Oval V-Groove cuts with a Feather, Decrease the Inside Oval Rotation.

A Bump in an Oval V-Groove is a Lump of material left behind where the cut started and ended on either the Outside or Inside Cut of the V-Groove.

The Oval Rotation for V-Grooves controls for Bumpsor Featherson an Oval V-Groove.

If the Inside Oval V-Groove cuts with a Bump, Increase the Inside Oval Rotation.

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Tool line is applied too far Left

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Tool line is applied too far Up

The Depth Setting controls the Blade Depth for the Non-Blade Tools in the Configurations.

If the Non-Blade Tool is

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Tools between segments.

The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. 

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

The Install Pen Utility calibrates the Pen Tool for use on the CMC.

The Pen Cartridge draws onto the surface of the matboard to create a design. In addition to templates, you can also Pen CutArts, LetterMats and TTFs.