Versions Compared

Old Version 36

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 37

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

Deboss Wide Configurations

Info

  • The Blue Deboss Wide Cartridge presses a wide stylus into the matboard to create a subtle design.

  • This is viewed from the front of the mat.

Expand
titleCartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Select the Deboss Wide Cartridge Type

  • Select the Deboss Tab on the Configurations screen.  

  • Select the Wide-Blue cartridge from the Cartridge dropdown control.

Tip

  • Deboss Wide

Select the Area of Concern for Wide Deboss Below:

  • Be sure to select the Deboss Wide from the Current Bevel Type dropdown control.

Deboss-Wide is Applied to the Wrong Place Horizontally

Problem:

  • The Deboss-Wide is applied to thewrong place Horizontallyapplied to thewrong place Horizontally.

  • This is viewed from the front of the mat.

Resolution:

Expand
titleHorizontal Adjustment Definition

The Horizontal Adjustment defines the global Horizontal placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Left Horizontally, Increase the Horizontal Adjustment.

If the Non-Blade Tool line is applied Too Far Right Horizontally, Decrease the Horizontal Adjustment.

Deboss-Wide is Applied to the Wrong Place Vertically 

Problem:

  • The Deboss-Wide is applied to the wrong place Vertically.

  • This is viewed from the front of the mat.

Resolution:

Expand
titleVertical Adjustment Definition

The Vertical Adjustment defines the global Vertical placement of objects applied with the Non-Blade Tool Cartridges.

If the Non-Blade Tool line is applied Too Far Up Vertically, Decrease the Vertical Adjustment.

If the Non-Blade Tool line is applied Too Far Down Vertically, Increase the Vertical Adjustment.

Deboss-Wide is the Wrong Size

Problem:

  • The Deboss-Wide is the Wrong Size.

  • This is viewed from the front of the mat.

Resolution:

Expand
titleOpening Adjustment Definition

The Opening Adjustment controls the size of the Opening cut or Object applied with non-blade cartridges.

If the Opening is cut Too Large, Decrease the Opening Adjustment.

If the Opening is cut Too Small, Increase the Opening Adjustment.

Deboss-Wide Applied at the Wrong Depth

Problem:

  • The Deboss-Wide is applied at the Wrong Depth.

  • This is viewed from the front of the mat.

Resolution:

Expand
titleDepth Setting Definition

The Depth Setting controls the Blade Depth for the Non-BladeTools in the Configurations.

If the Non-BladeTool is too Deep, Decrease the Depth Setting.

If the Non-BladeTool is too Shallow, Increase the Depth Setting.

Deboss-Wide Cartridge Tears the Mat 

Problem:

  • Deboss-Wide Cartridge Tears the Mat.

  • This is viewed from the front of the mat.

Resolution:

  • The Non-BladeTool is Tearing in the Corners of the segments, Increase the Corner Pause. 

  • The Non-BladeTool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause. 

  • See Corner Pause for additional information.

Expand
titleCorner Pause Definition

The Corner Pause setting in Configurations is the amount of time, in milliseconds, to pause the application of the Non-Blade Toolsbetween segments.

The Non-Blade Tool is Tearing in the Corners of the segments, Increase the Corner Pause. 

The Non-Blade Tool is Pausing Too Long in the Corners of the segments, Decrease the Corner Pause.  

Deboss-Wide Lines are too Long

Problem:

  • The Deboss-WideLines are Too Long.

  • This is viewed from the front of the mat.

Resolution:

  • If the Overshoot is applied too Long, Decrease the Overshoot.

  • See Overshoot for additional information.

Expand
titleOvershoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot of the Non-Blade Tool is applied Too Long, Decrease the Overshoot.

If the Overshoot of the Non-Blade Tool is applied Too Short, Increase the Overshoot.

Deboss-Wide Lines are too Short 

Problem:

  • The Deboss-WideLines are Too Short.

  • This is viewed from the front of the mat.

Resolution:

  • If the Overshoot is applied too Long, Decrease the Overshoot.

  • If the Overshoot is applied too Short, Increase the Overshoot.

  • See Overshoot for additional information.

Expand
titleOvershoot Definition

The Overshoot controls how far past the end of the Line/Arc Segment to apply the Non-Blade Tool (Deboss, Pen or Vinyl).

This is similar to the Overcut used with the Blade cartridges.

If the Overshoot is applied too Long, Decrease the Overshoot.

If the Overshoot is applied too Short, Increase the Overshoot.

Deboss-Wide Set to Plunge Between Segments

Problem:

  • The Deboss-Wide Set to Plunge Between Segments.

  • This is viewed from the front of the mat.

Resolution:

  • The Non-BladeTool leaves a Dot where it plunges, select Unplunge.

  • The Non-BladeTool takes Too Long to apply, select Plunge.

  • See Plunge for additional information.

Expand
titlePlunge Definition

The Plunge function controls whether to Plunge/Unplunge between the Line/Arc Segments of an object when applying a Non-Blade Tool.

The Non-Blade Tool leaves a Dot where it plunges, select Unplunge.

The Non-Blade Tool takes Too Long to apply, select Plunge.

Troubleshooting Button 

Info
Expand
titleTroubleshooting Button Definition

The Troubleshooting Utility allows you to bring in a single opening and automatically selects the correct Cartridge tab and Bevel Type to configure.

...