Versions Compared

Old Version 22

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 23

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Troubleshooting the Backup/Overcut Display

  • Have a cut design design displayed on the Cut Preview.

  • Note that this feature is only available for the Bladed Cartridges.

  • Using one of the Zoom buttons, zoom in to the desired section of the project where you are having issues cutting.

Image RemovedImage Added

  • Make sure that the Green Backups and Red Overcuts lines are visible.

Expand
titleExterior Backup Definition

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

If the Exterior Backup is cut too Short, it can leave a Hook in the corner.

If the Exterior Backup is cut too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut too Short, Increase the Exterior Backup.

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Expand
titleInterior Backup Definition

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Non-Oval Openings.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration.

If the Interior Backup is cut too Long, Decrease the Interior Backup.

If the Interior Backup is cut too Short, Increase the Interior Backup.

Expand
titleInterior Overcut Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

If the Interior Overcut is cut too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut too Short, Increase the Interior Overcut.

Image RemovedImage Added

  • With the cursor hovering over one of the Backups or Overcuts, the Status Bar displays the actual physical length of the selected Backup or Overcut.

  • This value will be the Sum of the corresponding User Configuration setting and the Factory Configuration setting.

Image RemovedImage Added

  • The cursor will turn into an arrow with a question mark.

  • Click on the desired Overcut or Backup line that you are having trouble with.

Expand
titleExterior Backup Definition

The Exterior Backup controls where the Blade Plunges into the Matboard (not the Fallout) on the Exterior cut. 

The Exterior Backup field is marked with a Green Arrow on the Configuration screen and the Map illustration.

If the Exterior Backup is cut too Short, it can leave a Hook in the corner.

If the Exterior Backup is cut too Long, Decrease the Exterior Backup.

If the Exterior Backup is cut too Short, Increase the Exterior Backup.

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Expand
titleInterior Backup Definition

The Interior Backup controls where the Blade Plunges into the Fallout (not the Matboard) on the Interior cuts of Non-Oval Openings.

The Interior Backup field is marked with a Black Arrow on the Configuration screen and the Map illustration.

If the Interior Backup is cut too Long, Decrease the Interior Backup.

If the Interior Backup is cut too Short, Increase the Interior Backup.

Expand
titleInterior Overcut Definition

The Interior Overcut controls where the Blade Retracts from the Fallout (not the Matboard) on the Interior cut.

The Interior Overcut field is marked with a White Arrow on the Configuration screen and the Map illustration.

If the Interior Overcut is cut too Long, Decrease the Interior Overcut.

If the Interior Overcut is cut too Short, Increase the Interior Overcut.

Tip
Image RemovedImage Added

  • The Configuration screen will open to the appropriate Cartridge Tab with the Configuration Field associated to the line clicked highlighted.

  • Now you can easily Increase or Decrease the value displayed, depending upon whether the item selecting is cutting Too Long or cutting Too Short.

  • Click OK and recut the design.

  • Continue adjusting the Configurations until you achieve the desired result.

Tip

  • To adjust, click Plus/Minus on the desired field about five times.

  • Click OK and do another test cut.

  • Continue making adjustments until the desired outcome is achieved.

Image RemovedIt will open the Configurations screen with the Cartridge selected and the specific Backup or Overcut field selected.		Image Added