Versions Compared

Version Old Version 20 New Version 21
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Info

Note: Not all cartridges are available for all CMC models.

Crease Cartridge Configurations

Info

  • The Crease Cartridge creases the material to make folding it easier when making Boxes.

  • This is viewed from the front of the mat.

Crease Tab

  • Select the Deboss Tab on the Configurations screen. 

  • Select the Crease Cartridge.

Tip

  • Crease Cartridge

Crease Exterior Backup is too Long

Problem:

  • The Crease Exterior Backup is too Long.

Expand
titleExterior Backup Definition

The Exterior Backup controls where the blade plunges into the matboard on the exterior cut. 

If the Exterior Backup is too short, it can leave a hook in the corner.

Exterior Backup cuts into the matboard, not the fallout.

The Exterior Backup field is marked with a Green Arrow.

Resolution:

  • Decrease the Exterior Backup.

  • See Exterior Backup for additional information.

info

Image Added

Crease Exterior Backup is too Short

Problem:

  • The Crease Exterior Backup is too Short.

Expand
titleExterior Backup Definition

The Exterior Backup controls where

the

the blade plunges

into

 into the matboard on the exterior

cutsCrease

cut. 

Image Removed Short

Problem:

The Crease Exterior Backup is too Short

If the Exterior Backup is too

short, it can leave a hook in the corner.

Exterior Backup cuts into the matboard, not the fallout.

The Exterior Backup field is marked with a Green Arrow.

Resolution:

  • Increase the Exterior Backup.

  • See Exterior Backup for additional information.

info

  • The Exterior Backup controls where the blade plunges into the matboard on exterior cuts.

The Exterior Overcut controls where the blade retracts

Crease Exterior Overcut is too Long

Problem:

  • The Crease Exterior Overcut is applied too Long.

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the blade retracts from the matboard on the exterior cuts.

Exterior Overcut cuts into the matboard, not the fallout.

The Exterior Overcut field is marked with a Red Arrow.

Resolution:

Info
Image Added
Crease

Crease Exterior Overcut is too Short

Problem:

  • The Crease Exterior Overcut is applied too Short.

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the blade retracts from the matboard on the exterior cuts.

Image Removed is too ShortThe Exterior Overcut controls where the blade retracts from the matboard on exterior cuts

  • .

Exterior Overcut

Problem:

The Crease Exterior Overcut is applied too Short

 cuts into the matboard, not the fallout.

The Exterior Overcut field is marked with a Red Arrow.

Resolution:

  • Increase the Exterior Overcut.

  • See Exterior Overcut for additional information.

Info
The Opening Adjustment controls the size of the opening

  • .

Crease is the Wrong Size

Problem:

  • Crease is applied at the Wrong Size.

Expand
titleOpening Adjustment Definition

The Opening Adjustment controls the size of the opening.

Resolution:

  • If cut too small, increase the Opening Adjustment.

  • If cut too large, decrease the Opening Adjustment.

  • See Opening Adjustment for additional information.

Info
The Depth Bias calculates the proper Blade Depth when a SKU is selected for the matboard

  • .

Crease is Applied at the Wrong Depth When Using a SKU

Problem:

  • The Crease is applied at the Wrong Depth When Using a SKU.

Expand
titleDepth Bias Definition

The Depth Bias calculates the proper Blade Depth when a SKU is selected for the matboard.

Resolution:

  • Cut too shallow, increase the Depth Bias.

  • Cut too deep, decrease the Depth Bias.

  • See Depth Bias for additional information.

Info

Troubleshooting Button 

Info

  • Select this topic to see information on editing with the Troubleshooting utility to make quick edits to the Configurations for a single object on the Cutting Preview. 

...