">

Click here to check out our new How To section">Click here to check out our new How To section
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 27 Next »

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

Exterior Overcut Definition

Adjusting the Exterior Overcut

  • To adjust, click plus/minus on the desired field about five times.

  • Click OK and do another test cut.

  • Continue making adjustments until the desired outcome is achieved.

 Exterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Select the Bevel Type for the Exterior Overcut to be Edited:

Exterior Overcut on Openings

Problem:

  • The Exterior Overcut on Openings is cut too long or too short.

  • Normal Bevel

  • Reverse Bevel

  • Normal Bevel-Front of Mat

  • Reverse Bevel-Front of Mat

Resolution:

 Exterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Exterior Overcut on Drops 

Problem:

  • The Exterior Overcut on Drops is cut too long or too short.

  • Normal Drop

  • Reverse Drop

  • Normal Drop-Front of Mat

  • Reverse Drop-Front of Mat

Resolution:

 Exterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Exterior Overcut on the Outside

Problem:

  • The Exterior Overcut for Outsides is cut too long or too short.

  • Outside

  • Outside-Front of Mat

Resolution:

 Exterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

Exterior Overcut on V-Grooves 

Problem:

  • The Exterior Overcut for V-Grooves is cut too long or too short.

  • V-Grooves

Resolution:

 V-Groove Exterior Overcut Definition

The V-Groove Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cuts of the Outside Cut of the V-Groove.

The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configurations screen and the Map illustration.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut too Short, Increase the Exterior Overcut.

Exterior Overcut on Creases

Problem:

The Exterior Overcut on Creases is applied too long or too short.

  • Crease

Resolution:

 Exterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut too Short, Increase the Exterior Overcut.

  • No labels