Page Comparison

If the original boxes cannot be located, replacement boxes can be purchased from Wizard at 888/855-3335.

Turn the shut off valve on the blue air line, and unplug the blue air line by untwisting the blue air fittings.

Turn the bottom locking knob clockwise to loosen.

Turn the top locking knob counter-clockwise to loosen.

Slide the straight line trimmer Straight Line Trimmer off of the boardBoard.

Fold the ends of the straight line trimmer Straight Line Trimmer packing inserts upwards.

Place the trimmer face-down into the recessed area, making sure that the trimmer handle is in the middle of the trimmer and that it is folded up next to the trimmer arm.

Fold the ends of the packing inserts down again, covering the ends of the trimmer.

Secure the box with tape.

If the motors are engaged, click reset motors button Reset Motors Button on the cut preview Cut Preview and click OK on the release motors prompt.

Press the 0 on the rocker switch on the back of the ECU to turn off the ECU.

Push blade cartridge release down to eject the blade cartridge. Turn off the air.

Remove the gantry Gantry cover by unscrewing the screws that holds it in place and set them aside.

Move the gantry Gantry to the right side of the board Board until the Footblock is off of the boardBoard.

For the CMC Z1, locate the M12 cable that is attached to the grabber arm.

Follow the M12 cable and unplug the other end from the M12 port at the top of the headHead, untwisting the thumbscrew to disconnect it.

For all models, remove the two 5/32” screws and set aside.

If present, remove the Head Assembly Power Cable Strain Relief from around the base sides of the Head Power Plug connection.

For all models, disconnect the head Head power plug (square connection) from the head Head grabber arm.

Disconnect the air to the head Head by untwisting the two air fittings.

Remove the head Head stop plate at the bottom of the gantry Gantry under the belt tensioner.

Two screws hold it in place. Set plate and screws aside.

Roll the head Head down the gantryGantry.

Roll the head Head down the gantry Gantry until it rolls off the gantryGantry, taking care not to drop it.

Replace the two 5/32” screws into the headHead.

Make sure the rocker switch on the back of the ECU is on the 0 for off.

Unplug the power cord.

Disconnect the male end of the board Board cable from the back of the ECU by turning the locking ring and pulling gently.

Unplug the USB Cable from the back of the ECU/Driver Pack.

If you have a CMC Z1, unplug the DB9 cable from the ECU.

Move the gantry Gantry to the right side of the board Board about two feet from the right edge (to leave room for the packaging foam corners).

Remove the 5/32” Allen screws and washers from the lower gantry Gantry plate.

Locate the 3/16” Allen belt tensioner screw that’s located on the right bottom side of the lower rail and marked with a red dot.

Loosen this screw one turn only so that there is some movement in the belt tensioner.

The tensioner springs should be visible.

The belt tensioner should spring fully into place.

Locate the belt tensioner hole on the end of the belt tensioner.

Place the 5/32” Allen screw and washer we removed from the lower gantry Gantry plate into the belt tensioner hole.

Tighten the Allen screw until belt tensioner is flush with the rail and the springs are not visible.

Go back and tighten the 3/16” Allen belt tensioner screw.

Lift the drive belt Drive Belt end out of the belt tensioner slot.

Pushing the drive belt Drive Belt end to the right may assist in getting a hold of it.

Wind up the drive beltDrive Belt, and rubber-band rubberband it.

Repeat steps 4 through 8 with the upper rail.

Move the gantry Gantry far enough to the left to dislodge the belt anchors.

The belt anchors are sunk into the left ends of the rails and are attached to the drive beltsDrive Belts.

See the instructions following for the type of Gantry Stop your machine has.

Loosen the top 3/16” stop screw Stop Screw of the Magnetic Gantry Stop.

Lift up the magnetic stop plate Magnetic Stop Plate to disengage the pin from the hole and slide the alignment plate to the left end of the rail to remove.

Remove the right front 3/16” stop screw Stop Screw of the silver Gantry Stop Plate and set aside.

Loosen the back left T-Nut screw and slide the alignment plate Gantry Stop Plate to the left end of the rail to remove.

If your model only has a Stop Screw without the alignment plate, remove the stop screwStop Screw.

If the shipping blocks have been misplaced, please find a way to secure the gantry Gantry so that it does not move during shipment.

Loosely place the T-Nut onto the shipping blocks and slide onto the rail on each side of the gantry Gantry as described next.

Place one shipping block on either side of the gantry Gantry on top of the upper rail.

Tighten into place.

Place the other two shipping blocks on the lower rail.

One should be to the left side of the gantry Gantry on the underside of the bottom rail and one on the top of the bottom rail. Tighten into place.

Place the other shipping block to the right of the gantry Gantry on the top of the bottom rail.

Slide the black Magnetic Gantry Stop Plate in from the left end of the rail keeping the pin towards you.

Place the pin into the hole and tighten the top 3/16” stop screwStop Screw.

Slide the alignment plate Gantry Stop Plate in from the left end of the rail and line up with the holes on the rail.

Tighten the back left T-Nut screw. Replace the right front 3/16” stop screw Stop Screw and tighten.

If your model only has a Stop Screw without the alignment plate, replace the stop screwStop Screw.

Lightly pull the coiled drive belt Drive Belt toward the right to take up the slack and pull the belt anchor into place flush with the end of the CMC.

Remove the rubber-band rubberband from the drive belt Drive Belt and loosely lay the drive belt Drive Belt along the rail channel.

Pull the loose belt end to the right, making sure that the drive belt Drive Belt is not twisted and that the teeth are facing down toward the board Board into the rail channel.

Slide the screw of the belt end into the belt tensioner slot.

Remove the 5/32” Allen screws and washers from the belt tensioner.

Place the two Allen screw and washer into the holes provided on the lower gantry Gantry plate.

Place them so that the screw protrudes only slightly from the back of the plate.

Loosen one full turn only the 3/16” Allen belt tensioner screw from the right bottom side of the lower rail marked with a red dot.

The belt tensioner should spring fully into place.

Snugly tighten the Allen belt tensioner screw on the bottom right of upper and lower rails.

Repeat steps 1 through 5 with the upper rail.

Replace the gantry Gantry cover using the two screws removed earlier.

Place the packaging foam in the bottom of the head Head box with the cradle toward the center.

Place the head Head upside down into the cradle; you may need to rotate the Footblock.

Place the remaining portion of the head Head packaging foam across the bottom of the head Head and around each side; press into place.

Close and tape up the box.

Locate the ECU packaging foam and fold out the interior feet.

Place the packaging foam on each end of the ECU/Driver Pack.

Place the ECU/Driver Pack carefully into the ECU/Driver Pack box.

Place all of the ECU/Driver Pack and emergency stop cables (if applicable) into the free space and tape shut.