Exterior Overcut on Openings
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Exterior Overcut of Openings Definition |
|---|
The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).
If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.
If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.
The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.
See: Exterior Overcut for Openings Configurations
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Exterior Overcut on Drops
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Exterior Overcut of Drops Definition |
|---|
The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).
If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.
If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.
The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.See: Exterior Overcut for Drops Configurations
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Exterior Overcut on the Outside
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Exterior Overcut on Outsides Definition |
|---|
The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).
If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.
If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.
The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.See: Exterior Overcut for the Outside Configurations
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Exterior Overcut on V-Grooves
| panelIconId | atlassian-note |
|---|---|
| panelIcon | :note: |
| bgColor | #B3F5FF |
If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut.
| title | V-Groove Exterior Overcut of V-Grooves Definition |
|---|
The Exterior Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).
If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decreasethe Exterior Overcut.If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut.
The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.See: V-Groove Exterior Overcut Configurations
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Exterior Overcut on Creases
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
|
| title | Exterior Overcut of Creases Definition |
|---|
If the Overcut is Too Long, Decrease the Exterior Overcut.
If the Overcut is Too Short, Increase the Exterior Overcut.
The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.See: Overcut for Creases Configurations
| Expand | ||
|---|---|---|
| ||
When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
Contents:
|
|