Page Comparison

Cartridges Involved

This Configuration element involves the following Cartridges.

Info
Note: Not all cartridges are available for all CMC models.

Image Removed

Bevel Type Examples

Reverse Bevel Drop

Info
A Reverse Bevel Drop is the fallout that is cut from the back* of the mat, which does not display an exposed bevel on the face of the matboard. When cutting a Reverse Bevel Open V-Groove, the inside cut uses the Reverse Bevel Drop bevel configuration and the outside cuts with a Reverse Bevel Opening configuration.

Tip

*See Reverse Bevel Drop - Front of Mat below for editing configurations when cutting from the front of the mat.

**See 45 Degree Front Reverse Bevel Drop - Front of Mat below for the 45 Degree Front Cartridge Configurations.

Expand

title	Reverse Drop Definition

The Reverse Drop is when the Angle of the blade cuts the Fallout surface so it Slants Under the surface of the Fallout, and the Matboard Core is Not Seen from the front.

Cutting From the Back will cut with the face of the mat toward the CMC Board, and can be selected on the Cutting Preview.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Reverse Dropfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Outside Bevel

Info
An Outside Bevel is the outside cut of the mat that is cut from the back* of the mat, and does not display an exposed bevel on the face of the matboard.

45 Degree Outside Bevel

45 Degree Plus Outside Bevel

**45 Degree Front Outside Bevel - Front of Mat

52 Degree Outside Bevel90 Degree Outside Bevel

Tip

*See Outside Bevel - Front of Mat below for editing configurations when cutting from the front of the mat.

**See 45 Degree Front Outside Bevel - Front of Mat below for the 45 Degree Front Cartridge Configurations.

Expand

title	Outside Bevel Definition

The Outside Bevel is when the Angle of the blade cuts the Fallout surface so it Slants Under the surface of the Fallout, and the Matboard Core is Not Seen from the front.

Cutting From the Back will cut with the face of the mat toward the CMC Board, and can be selected on the Cutting Preview.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Outsidefrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Normal Bevel Opening - Front of Mat

Info
A Normal Bevel Opening - Front of Mat opening is cut from the front* of the mat, and displays an exposed bevel in the face of the matboard.

Tip
See Normal Bevel Opening* above for editing configurations when cutting from the back of the mat.

Expand

title	Normal Bevel - Front of Mat Definition

The Normal Bevel - Front of Mat is when the Angle of the blade cuts the Matboard surface so it Slants Away from the surface of the Matboard, and the Matboard Core is Seen from the front. Also referred to as Standard or Forward bevel.

Cutting From the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview or by cutting a Cut-From-Front element such as a Deboss or V-Groove.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Normal Bevel - Front of Matfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Reverse Bevel Opening - Front of Mat

Info
A Reverse Bevel Opening - Front of Mat opening is cut from the front* of the mat, and does not display an exposed bevel in the face of the matboard.

Tip
See Reverse Bevel Opening* above for editing configurations when cutting from the back of the mat.

Expand

title	Reverse Bevel - Front of Mat Definition

The Reverse Bevel - Front of Mat is when the Angle of the blade cuts the Matboard surface so it Slants Under the surface of the Matboard, and the Matboard Core is Not Seen from the front.

Cutting From the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview or by cutting a Cut-From-Front element such as a Deboss or V-Groove.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Reverse Bevel - Front of Matfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Normal Bevel Drop - Front of Mat

Info
A Normal Bevel Drop - Front of Mat is the fallout that is cut from the front* of the mat, which displays an exposed bevel on the face of the matboard. When cutting a Normal Bevel Open V-Groove from the front, the inside cut uses the Normal Bevel Drop - Front of Mat bevel configuration and the outside cuts with a Normal Bevel Opening - Front of mat configuration.

Tip
See Normal Bevel Drop* above for editing configurations when cutting from the back of the mat.

Expand

title	Normal Drop - Front of Mat Definition

The Normal Drop is when the Angle of the blade cuts on the Fallout surface so it Slants Away from the surface of the Fallout, and the Matboard Core is Seen from the front.

Cutting From the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview or by cutting a Cut-From-Front element such as a Deboss or V-Groove.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Normal Drop - Front of Matfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Reverse Bevel Drop - Front of Mat

Info
A Reverse Bevel Drop - Front of Mat is the fallout that is cut from the front* of the mat, which does not display an exposed bevel on the face of the matboard. When cutting a Reverse Bevel Open V-Groove from the Front, the inside cut uses the Reverse Bevel Drop - Front of Mat bevel configuration and the outside cuts with a Reverse Bevel Opening - Front of Mat configuration.

Tip
See Reverse Bevel Drop* above for editing configurations when cutting from the back of the mat.

Expand

title	Reverse Drop - Front of Mat Definition

The Reverse Drop - Front of Mat is when the Angle of the blade cuts the Fallout surface so it Slants Under the surface of the Fallout, and the Matboard Core is Not Seen from the front.

Cutting From the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview or by cutting a Cut-From-Front element such as a Deboss or V-Groove.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Reverse Drop - Front of Matfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Outside Bevel - Front of Mat

Info
An Outside Bevel - Front of Mat is the outside cut of the mat that is cut from the front* of the mat, which does not display an exposed bevel on the face of the matboard.

45 Degree Outside Bevel - Front of Mat

45 Degree Plus Outside Bevel - Front of Mat

45 Degree Front Outside Bevel - Front of Mat

52 Degree Outside Bevel - Front of Mat90 Degree Outside Bevel - Front of Mat

Tip
See Outside Bevel* above for editing configurations when cutting from the back of the mat.

Expand

title	Outside Bevel - Front of Mat Definition

The Outside Bevel - Front of Mat is when the Angle of the blade cuts the Fallout surface so it Slants Under the surface of the Fallout, and the Matboard Core is Not Seen from the front.

Cutting From the Front will cut with the face of the mat toward the operator, and can be selected on the Cutting Preview or by cutting a Cut-From-Front element such as a Deboss or V-Groove.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Outside Bevel - Front of Matfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Closed V-Groove

Info
A Closed V-Groove is a thin channel cut into the face of the matboard to reveal the matboard core color. It is cut from the front of the mat, and any other openings on that layer will also be cut from the front.

45 Degree Closed V-Groove45 Degree Plus Closed V-Groove

45 Front Closed V-Groove

52 Degree Closed V-Groove

Panel

panelIconId	atlassian-check_mark
panelIcon	:check_mark:
bgColor	#FFF0B3

First Cut of the Closed V-Groove

Cuts the Interior V-Groove Line.
Cuts into fallout, not the matboard.
Cuts clockwise.

Panel

panelIconId	atlassian-check_mark
panelIcon	:check_mark:
bgColor	#FFF0B3

Second Cut of the Closed V-Groove

Cuts the Exterior V-Groove Line.
Cuts into matboard, not the fallout.
Cuts counter-clockwise.

Expand

title	V-Groove Definition

A Normal Bevel Closed V-Groove consists of two cuts - one in the Matboard and one in the Fallout, mirroring each other. They are cut Halfway through the matboard, revealing the Matboard Core.

The Normal Bevel is when the Angle of the blade cuts the Matboard/Fallout surface so it Slants Away from the surface of the Matboard/Fallout, and the Matboard Core is Seen from the front.

Image Removed

Open V-Groove

Normal Bevel Open V-Groove

Info
A Normal Bevel Open V-Groove consists of two cuts - one in the Matboard and one in the Fallout, mirroring each other, spaced a specified distance away. They are cut through the matboard, revealing the lower layer matboard in the exposed segment.

Panel

panelIconId	atlassian-check_mark
panelIcon	:check_mark:
bgColor	#FFF0B3

First Cut of the Normal Bevel Open V-Groove

Cuts the Interior V-Groove Line.
Cuts into Fallout, not the matboard.
Cuts Clockwise.
45 Degree Normal Bevel Drop
45 Degree Normal Bevel Drop - Front of Mat

Panel

panelIconId	atlassian-check_mark
panelIcon	:check_mark:
bgColor	#FFF0B3

Second Cut of the Normal Bevel Open V-Groove

Cuts the Exterior V-Groove Line.
Cuts into Matboard, not the fallout.
Cuts Counter-Clockwise.
45 Degree Normal Bevel Opening
45 Degree Normal Bevel Opening - Front of Mat

Expand

title	Open V-Groove Definition

A Normal Bevel Open V-Groove consists of two cuts - one in the Matboard and one in the Fallout, mirroring each other, spaced a specified distance away. They are cut Through the matboard, revealing the Lower Layer Matboard in the exposed segment.

The Normal Bevel is when the Angle of the blade cuts the Matboard/Fallout surface so it Slants Away from the surface of the Matboard/Fallout, and the Matboard Core is Seen from the front.

Image Removed

Reverse Bevel Open V-Groove

Info
A Reverse Bevel Open V-Groove consists of two cuts - one in the Matboard and one in the Fallout, mirroring each other, spaced a specified distance away. They are cut through the matboard, revealing the lower layer matboard in the exposed segment.

Panel

panelIconId	atlassian-check_mark
panelIcon	:check_mark:
bgColor	#FFF0B3

First Cut of the Reverse Bevel Open V-Groove

Cuts the Interior V-Groove Line.
Cuts into Fallout, not the matboard.
Cuts Clockwise.
45 Degree Reverse Bevel Drop
45 Degree Reverse Bevel Drop - Front of Mat

Panel

panelIconId	atlassian-check_mark
panelIcon	:check_mark:
bgColor	#FFF0B3

Second Cut of the Reverse Bevel Open V-Groove

Cuts the Exterior V-Groove Line.
Cuts into Matboard, not the fallout.
Cuts Counter-Clockwise.
45 Degree Reverse Bevel Opening
45 Degree Reverse Bevel Opening - Front of Mat

Expand

title	Reverse Bevel Open V-Groove Definition

A Reverse Bevel Open V-Groove consists of two cuts - one in the Matboard and one in the Fallout, mirroring each other, spaced a specified distance away. They are cut Through the matboard, revealing the Lower Layer Matboard in the exposed segment.

The Reverse Bevel is when the Angle of the blade cuts the Matboard surface so it Slants Under the surface of the Matboard, and the Matboard Core is Not Seen from the front.

First Cut of the Reverse Bevel Open V-Groove

Cuts the Interior V-Groove Line.

Cuts into Fallout, not the matboard.

Cuts Clockwise.

45 Degree Reverse Bevel Drop

45 Degree Reverse Bevel Drop - Front of Mat

Second Cut of the Reverse Bevel Open V-Groove

Cuts the Exterior V-Groove Line.

Cuts into Matboard, not the fallout.

Cuts Counter-Clockwise.

45 Degree Reverse Bevel Opening

45 Degree Reverse Bevel Opening - Front of Mat

Image Removed

Bevel Type Examples

Info
The examples below display the different bevel types that can be cut with the bladed cartridges.

To edit, select the desired Cartridge Type Tab on the Configurations Screen.
Select the desired bevel type to edit from the Current Bevel Type dropdown control.

Expand

title	Bevel Type Definition

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Image Removed

Normal Bevel Opening

Info
A Normal Bevel Opening is cut from the back* of the mat, and displays an exposed bevel in the face of the matboard.

Tip

*See Normal Bevel Opening - Front of Mat below for editing configurations when cutting from the front of the mat.

**See 45 Degree Front Normal Bevel Opening - Front of Mat below for the 45 Degree Front Cartridge Configurations.

Expand

title	Normal Bevel Definition

The Normal Bevel is when the Angle of the blade cuts the Matboard surface so it Slants Away from the surface of the Matboard, and the Matboard Core is Seen from the front. Also referred to as Standard or Forward bevel.

Cutting From the Back will cut with the face of the mat toward the CMC Board, and can be selected on the Cutting Preview.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Normal Bevelfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Reverse Bevel Opening

Info
A Reverse Bevel Opening is cut from the back* of the mat, and does not display an exposed bevel in the face of the matboard.

Tip

*See Reverse Bevel Opening - Front of Mat below for editing configurations when cutting from the front of the mat.

**See 45 Degree Front Reverse Bevel Opening - Front of Mat below for the 45 Degree Front Cartridge Configurations.

Expand

title	Reverse Bevel Definition

The Reverse Bevel is when the Angle of the blade cuts the Matboard surface so it Slants Under the surface of the Matboard, and the Matboard Core is Not Seen from the front.

Cutting From the Back will cut with the face of the mat toward the CMC Board, and can be selected on the Cutting Preview.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Reverse Bevelfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Normal Bevel Drop

Info
A Normal Bevel Drop is the fallout that is cut from the back* of the mat, which displays an exposed bevel on the face of the matboard. When cutting an Open V-Groove, the inside cut uses the Normal Bevel Drop bevel configuration and the outside cuts with a Normal Bevel Opening configuration.

Tip

*See Normal Bevel Drop - Front of Mat below for editing configurations when cutting from the front of the mat.

**See 45 Degree Front Normal Bevel Drop - Front of Mat below for the 45 Degree Front Cartridge Configurations.

Expand

title	Normal Drop Definition

The Normal Drop is when the Angle of the blade cuts on the Fallout surface so it Slants Away from the surface of the Fallout, and the Matboard Core is Seen from the front.

Cutting From the Back will cut with the face of the mat toward the CMC Board, and can be selected on the Cutting Preview.

The Bevel Type is the Angle that the blade cuts on the Matboard/Fallout surface when it is not cut at a 90° Right Angle.

Select Normal Dropfrom the Current Bevel Type dropdown control to edit this configuration.

Image Removed

Image Added

Normal Bevel Opening

Insert excerpt

	Normal Bevel Opening
	Normal Bevel Opening
name	Normal Bevel Opening
nopanel	true

Image Added

Reverse Bevel Opening

Insert excerpt

	Reverse Bevel Opening
	Reverse Bevel Opening
name	Reverse Bevel Opening
nopanel	true

Image Added

Normal Bevel Drop

Insert excerpt

	Normal Bevel Drop
	Normal Bevel Drop
name	Normal Bevel Drop
nopanel	true

Image Added

Reverse Bevel Drop

Insert excerpt

	Reverse Bevel Drop
	Reverse Bevel Drop
name	Reverse Bevel Drop
nopanel	true

Image Added

Outside Bevel

Insert excerpt

	Outside Bevel
	Outside Bevel
name	Outside Bevel
nopanel	true

Image Added

Closed V-Groove

Insert excerpt

	v-groove
	v-groove
name	V-Groove
nopanel	true

Image Added

Normal Bevel Open V-Groove

Insert excerpt

	45 Degree Normal Bevel Open V-Groove
	45 Degree Normal Bevel Open V-Groove
name	45 Degree Normal Bevel Open V-Groove
nopanel	true

Image Added

Reverse Bevel Open V-Groove

Insert excerpt

	Reverse Bevel Open V-Groove
	Reverse Bevel Open V-Groove
name	Reverse Bevel Open V-Groove
nopanel	true

Image Added

Cartridge Type Examples

Info
See Cartridge Type Examples for examples of the different cartridge types that can be selected from the Cartridge Type Tabs. Note: Not all cartridges are available for all CMC models.

Expand

title	Cartridge Definition

A Cartridge is the physical component that holds a Blade, Deboss Stylus, Pen or other application tool.

Image Removed

Image Added

Versions Compared

Old Version 38

New Version 59

Key

Cartridges Involved

Bevel Type Examples

Reverse Bevel Drop

Outside Bevel

Normal Bevel Opening - Front of Mat

Reverse Bevel Opening - Front of Mat

Normal Bevel Drop - Front of Mat

Reverse Bevel Drop - Front of Mat

Outside Bevel - Front of Mat

Closed V-Groove

First Cut of the Closed V-Groove

Second Cut of the Closed V-Groove

Open V-Groove

Normal Bevel Open V-Groove

First Cut of the Normal Bevel Open V-Groove

Second Cut of the Normal Bevel Open V-Groove

Reverse Bevel Open V-Groove

First Cut of the Reverse Bevel Open V-Groove

Second Cut of the Reverse Bevel Open V-Groove

First Cut of the Reverse Bevel Open V-Groove

Second Cut of the Reverse Bevel Open V-Groove

Bevel Type Examples

Normal Bevel Opening

Reverse Bevel Opening

Normal Bevel Drop

Normal Bevel Opening

Reverse Bevel Opening

Normal Bevel Drop

Reverse Bevel Drop

Outside Bevel

Closed V-Groove

Normal Bevel Open V-Groove

Reverse Bevel Open V-Groove

Cartridge Type Examples