Versions Compared

Version Old Version 14 New Version Current
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Info

Change Start

Panel
panelIconIdatlassian-info
panelIcon:info:
bgColor#B3F5FF

  • Use the Change Start button to change the Start Cutting Point of an object. 

Through Nesting, another design may be cut within the fallout.

Image Removed

See: Drops Definition

Image Removed

Display Start Points

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • There are a number of reasons to change the Cut Start.

    • If you are having difficulties cutting a complex design and the blades are breaking or it is skipping steps, it may help to start the cut in a different place, such as in a corner rather than in the middle of two arcs. 

    • You may also want to do this if you are having problems with Fallouts sliding behind the mat you are cutting. Changing Cut Order and Changing Start Cut Points may resolve some of these issues.

Expand
titleFallout Definition

The Fallout is the part of the mat that is removed when a design is cut.

Typically, the Falloutis discarded, or saved for another project if large enough.Sometimes the Falloutis considered as part of the design, such as the Dropouts on the inner portions of LetterMat letters.

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

ChangeStart70800.pngImage Added

Display Start Points

Info

  • The initial Blade Plunge and Cut Direction will be displayed as a triangle arrow.

Image Removed
Image Added

Select the Type of Object

PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FF

  • Select the desired Bevel/Cartridge Type you wish to change the initial plunge for from the Bevel/Cartridge Type Selection section by clicking the radio button next to it. 

Info

  • Only the objects matching the Bevel/Cartridge Type selection will be displayed. 

  • The other Bevel/Cartridge Types of the design on the screen will be grayed out.

expand

Insert excerpt

title
Expand
titleCartridge Definition

A Cartridge is the physical component that holds the Blade, Deboss Stylus, Pen or other application tool.

Image Removed
Image Removed

Changing the Start

PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FF

Cartridge

Bevel Type Definition

The Bevel Type refers to the angle at which the blade cuts the surface of the matboard when it deviates from the 90° right angle cut.

Image Removed

Cartridge
nameCartridge Definition

Image Added
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

Changing the Start

  • Select the object you want to edit by clicking on it.

Image Removed
Image Added

  • Click the Change Start button.

    • This will allow you to change the initial plunge for the object.

Image Removed PanelpanelIconIdatlassian-notepanelIcon:note:bgColor#B3F5FF
Image Added

  • Move the Blue Triangle cursor to where you want the initial blade plunge to start when it cuts this object.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Click to place the new start point of the initial Blade Plunge.

Info

  • The Start Point of this object has now been changed.

Image Removed Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Image Added

  • Do the same with the other openings.

Info

  • In this example, the openings will begin cutting at the bottom left corner instead of at the top left corner. 

Image Removed
Image Added