Page Comparison

NOTE: A Blade has been installed, so take care when handling the Straight Line Trimmer.

Look at the backside of the Trimmer and locate the T-Nut on the glides. Make sure that the T-Nut lines up with the glide on both the upper and lower sections of the Trimmer.

Holding the Straight Line Trimmer steady (a second person helps here), carefully slide the Trimmer onto the channels on the right side of the Board, making sure that the T-Nuts slide into the channel of both the upper and lower rails.

Go back and make sure that the Air Lines on the back of the Board are not pinched between the Board and the Stand. If you have not already done so, reattach the Air Lines on the inside of the Stand Arms to ensure maximum air flow.

Connect the Blue Connector from the top of the ST 500 to the Blue Connector/Shut Off Valve of the “Y” Connector.

Connect Red Connector from the top of the Gantry to the Red Connector of “Y” Connector; only one side will fit.

Plug in the Red Air Line Connector from the bottom of the “Y” into the right side of the Air Regulator.

Plug the Air Line coming off the left side of the Air Regulator into your main air supply via 1/4” NPT female connector, or the quick disconnect, whichever type you purchased. Your air compressor should have at least 100 - 120 PSI. It is suggested that Teflon tape be used on the threads of the black fitting to reduce possible air leakage.

Strap your Air Regulator, glass bowl down to the left large wall bracket or left stand side with cable ties provided in your Tool Kit, making sure not to crimp any of the Air Lines.

Connect Blue Connector from the top of the Gantry to the Blue Connector on the back of the Board.

Turn on the Air.

WARNING: The Air Regulator comes factory-set. Do not make any adjustments to it.

Continue to Calibration and Alignment of the Straight Line Trimmer.

Locate the Air Valve on the back of the Board on the right side. Note the three connections from the Air Valve.

Take the Clamp Valve Plug (Grey cable with the Green Power Plug) and plug it into the Clamp Valve (the matching Green Plug on the top of the Gantry).

Take the Clear Air Line with the Red Connector from the Air Valve and Plug it into the Air Line with the Red Connector at the top of the Gantry by giving it a 1/4 turn onto the locking connector.

The top of the Straight Line Trimmer has an Air Line coming out of the back it, which connects to a Blue Connector/Shut Off Valve on a “Y” Connector.

Take the Black Air Line with the Red Connector from the Air Valve and Plug it into the Red Connector of the “Y” on the Straight Line Trimmer. Only one will fit.

NOTE: If you did not install the ST 500, this Black Air Line with the Red Connector would plug into the right side of the Air Regulator.

Plug in the other Air Line with the Red Connector of the “Y” into the right side of the Air Regulator.

Plug the Air Line coming off the Left side of the Air Regulator into your main air supply via 1/4” NPT female connector, or the quick disconnect, whichever type you purchased. Your air compressor should have at least 100 - 120 PSI. Shown below is the black threaded fitting connected to a 1/4” NPT female adaptor. It is suggested that Teflon tape be used on the threads of the black fitting to reduce possible air leakage.

Strap your Air Regulator, glass bowl down to the left large wall bracket or left stand side with cable ties provided in your Tool Kit, making sure not to crimp any of the Air Lines.

Turn on the Air.

Continue to Calibration and Alignment of the Straight Line Trimmer.

WARNING: The Air Regulator comes factory-set. Do not make any adjustments to it.

Do not use the Wizard to cut anything wider than 53” from the left edge of the matboard while the Straight Line Trimmer is installed, or you will risk having the Head collide with the Straight Line Trimmer. This includes the outside cut. If you need to cut something that is larger than 53” from the left edge of the matboard, you will need to temporarily remove the Straight Line Trimmer.

Do not use the Wizard to cut anything wider than 53” from the left edge of the matboard... this INCLUDES the outside cut... without first removing the Straight Line Trimmer.