Page Comparison

Cut the Outside On

Info
Use the Cut the Outside toggle to select Cutting or Not Cutting the Outside of the mat.

Click the Cut Outside toggle On to cut the outside of the mat.
The outside of the mat will now cut.
Optionally, select Options > Cut Outside.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information:
See Matboard Properties in the Design to turn on/off the Outside cut.
Select Options Menu > Cut Outside on the Cut Previewto cut the outside of the mat.
See /wiki/spaces/FrameShop8x/pages/1942506497 on the Cut Previewto turn on/off the Outside cut.
See Enable Outside Cutunder Advanced Outside Options on the Cut Previewto toggle on/off the Outside cut.
See Cut Outside Using 90 Degree Tool under Set Advanced Optionson the Cut Preview.
See Cut Mode in the Set Advanced Options section on the Cut Preview.
See Shared Edge for the Cut Mode in the Set Advanced Options section on the Cut Preview
See Full for the Cut Mode in the Set Advanced Options section on the Cut Preview.
See As Designed for the Cut Mode in the Set Advanced Options section on the Cut Preview.
See Remnant Trimming in the Set Advanced Options section on the Cut Preview.

Tip

Default Settings:
See Admin > Editor to set the default of whether or not to Cut the Outside.
See Admin > Editor for the default settings for Cutting the Outside.
See Admin > Cutting for the default settings for the Advanced Options.
See Admin > Cutting for the default settings for the Cut Mode.
See Admin > Cutting for the default settings for 90 Degree Outside.
See Admin > Cutting for the default settings for Tiling.
See Admin > Cutting for the default size for the Spacing between designs.

Cut the Outside Off

Click the Cut Outside toggle Off to not cut the outside of the mat.
The outside of the mat will not be cut.

Tip
Default Settings: See Admin > Editor to set the default of whether or not to Cut the Outside. See Admin > Editor for the default settings for Cutting the Outside. See Admin > Cutting for the default settings for the Advanced Options.

Auto Offset

Info
Use the Auto Offset checkbox to move the design up and over on the matboard to avoid the clamp area.

Click on the design to select it.
Check the Auto Offset checkbox.
Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value.
It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.
This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Auto Offset on the Location Tab on the Cut Preview.

Tip
Default Settings: See Admin > Cutting for the default settings for the Auto Offset.

Expand

title	Auto Offset Definition

The Auto Offset moves the design up and over on the Cut Preview to avoid the Clamparea.

This is to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

Image Removed

See: Auto Offset Setting

See: Auto Offset Definition

See: Auto Offset Default Setting

Image Removed

Disable Auto Offset

Info
Disabling the Auto Offset will cut the design normally without being offset.

Click on the design to select it.
Uncheck the Auto Offset checkbox.
The design will no longer be offset and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.
This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

Panel

panelIconId	1f9d9-200d-2642-fe0f
panelIcon	:man_mage:
panelIconText	🧙‍♂️
bgColor	#FFFAE6

For Additional Information: See Auto Offset on the Location Tab on the Cut Preview.

Tip
Default Settings: See Admin > Cutting for the default settings for the Auto Offset.

Expand

title	Auto Offset Definition

The Auto Offset moves the design up and over on the Cut Preview to avoid the Clamparea.

This is to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

Image Removed

See: Auto Offset Setting

See: Auto Offset Definition

See: Auto Offset Default Setting

Image Removed

Versions Compared

Old Version 32

New Version 33

Key

Cut the Outside On

Cut the Outside Off

Auto Offset

Disable Auto Offset