Versions Compared

Version Old Version 35 New Version 36
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

X and Y Origin

Info

  • Use the X Origin (Horizontal) and Y Origin (Vertical) fields to move the design to the specific location to cut.

  • Click on the design to select it.

  • Enter a new X or Y Origin value and tab out of the field.

  • It will move the lower left corner point of the design to the new X/Y Position on the Cut Preview Screen.

  • Previous Cuts are displayed in Faded Grey to help the user position the current design on the screen.

  • To clear the Previous Cuts from the screen, click Clear Cut History.

Expand
titleX Position Definition

The X Position field is used to set or display the Horizontal position of the selected object in Designer, Trace and the Cut Preview. 

Expand
titleY Position Definition

The Y Position field is used to set or display the Vertical position of the selected object in Designer, Trace and the Cut Preview. 

Expand
titlePrevious Cuts Definition

The Previous Cuts are displayed on the Cut Preview as Faded Gray outlines.

These allow you to position the next cut beside a previous cut when cutting several designs from the same mat, such as when Calibrating the CMC.

This can be turned on/off in the Options menu, and the previous cuts can be cleared from the screen with the Clear Cut History button.

See: Previous Cuts Toggle

See: Clear Cut History

...

Enable Auto Offset

Info

  • Select Auto Offset checkbox to move the design up and over on the matboard to avoid the Clamp area on the Cut Preview.

Tip

  • Click on the design to select it.

  • Check the Auto Offset checkbox.  

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.

  • This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

Expand
titleAuto Offset Definition

The Auto Offset moves the design up and over on the Cut Preview to avoid the Clamparea.

This is to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

See: Auto Offset Setting

See: Auto Offset Definition

See: Auto Offset Default Setting

Disable Auto Offset

Info

  • Disabling the Auto Offset will cut the design normally without being offset into the mat.

Tip

  • Click on the design to select it.

  • Uncheck the Auto Offset checkbox.

  • The design will no longer be offset and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

  • This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

Info

  • Note: The outside cut is shown here merely for visual reference of where the pre-cut matboard will be positioned on the board. This feature can also be used to move the design to avoid flaws in the matboard.

Expand
titleAuto Offset Definition

The Auto Offset moves the design up and over on the Cut Preview to avoid the Clamparea.

This is to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

See: Auto Offset Setting

See: Auto Offset Definition

See: Auto Offset Default Setting

...

Home Button

Info

  • The Home button will return the current design back to the Home position on the Cut Preview screen after cutting it elsewhere on the board.

  • Click on the design to select it.

  • Click the Home button.

  • The current design will be returned to the Home position on the Cutting Cut Preview Screen.

Clear Cut History Button

Info
Tip

  • The Previous Cuts on the screen are drawn out in Faded Gray outlines.

  • Click the Clear Cut History button.

  • The Previous Cuts on the screen are erased.

  • This is helpful when the previous cuts are a distraction for the current session, or you no longer need them as a reference when moving the position of the current design to cut.

Expand
titlePrevious Cuts Definition

The Previous Cuts are displayed on the Cut Preview as Faded Gray outlines.

These allow you to position the next cut beside a previous cut when cutting several designs from the same mat, such as when Calibrating the CMC.

This can be turned on/off in the Options menu, and the previous cuts can be cleared from the screen with the Clear Cut History button.

See: Previous Cuts Toggle

See: Clear Cut History

...