Versions Compared

Old Version 25

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 26

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Note: You can also

Cut the Outside On  

Info

  • Use the Cut the Outside toggle to select Cutting or Not Cutting the Outside of the mat.

  • Click the Cut Outside toggle On to cut the outside of the mat.

  • The outside of the mat will now cut. 

Info
Image Removed

Cut the Outside Off

Click the Cut Outside toggle Off to not

Panel
panelIconId1f9d9-200d-2642-fe0f
panelIcon:man_mage:
panelIconText🧙‍♂️
bgColor#FFFAE6

  • The outside of the mat will not be cut.

    • Image RemovedSet Advanced
    Panel
    panelIconId1f9d9-200d-2642-fe0f
    panelIcon:man_mage:
    panelIconText🧙‍♂️
    bgColor#FFFAE6
    Optionally, the Outside cut can be turned on or off from the Advanced Outside Options: Enable Outside Cut toggle

    • to turn on/off the Outside cut for the CMC Z1, Z(9000z), 9000 and 8000+.

    Image Removed

    Defaults: Set the Default for Cutting the Outside 

    Expand
    titleDefault Settings for Cutting the Outside
    The
    Tip
     can be set in the Admin > Editor section.Image Removed

    Defaults: Set the Default for 90 Degree Outside Cut

    Expandtitle

    • .

    Tip

    • Default Settings

    for Cutting the Outside with the 90 Degree CartridgeThe default setting for 
    can be set in the Admin > Cutting section

    • for the CMC Z1, Z(9000z), 9000 and 8000+.

    Note that the CMC 8000 does support cutting with the 90 Degree Cartridge.

    Image Removed

    		Image Added

    Cut the Outside Off

    • Click the Cut Outside toggle Off to not cut the outside of the mat.

    • The outside of the mat will not be cut.

    		Image Added

    Auto Offset

    Info

    • Select Auto Offset checkbox to move the design up and over on the matboard to avoid the clamp area.

    • Click on the design to select it.

    • Check the Auto Offset checkbox.  

    • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

    • It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.

    • This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

    Tip
    Expand
    titleAuto Offset Definition

    The Auto Offset moves the design up and over on the Cut Preview to avoid the Clamparea.

    This is to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

    See: Auto Offset Setting

    See: Auto Offset Definition

    See: Auto Offset Default Setting

    See Also: Options Menu: Cut Outside

    Info

    • Optionally, you can use the Options menu to cut the outside of the design.

  • Click on the design to select it.

  • Click Options > Cut Outside to cut the outside of the mat.

    • It will now cut the outside of the mat.

    Disable Auto Offset

    Info

    • Disabling the Auto Offset will cut the design normally without being offset.

    • Click on the design to select it.

    • Uncheck the Auto Offset checkbox.

    • The design will no longer be offset and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

    • This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

    Tip
    Expand
    titleAuto Offset Definition

    The Auto Offset moves the design up and over on the Cut Preview to avoid the Clamparea.

    This is to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

    See: Auto Offset Setting

    See: Auto Offset Definition

    See: Auto Offset Default Setting

    		Image Removed

    Defaults: Set the Default for the Auto Offset

    Expand
    titleSet the Default to Enable Auto Clamp Offset

    The default setting and offset value for the Auto Offset can be set in the Admin > Cutting section.

    Image Removed

    		Image Modified