Page Comparison

• Exterior Overcut on Openings cuts Too long or Too short.

The Exterior Overcut controls where the Blade Retracts the BladeRetracts from the Matboard (not the Fallout) on the Exterior cutcuts of Openings.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

Image AddedImage Added

See: Exterior Overcut for Openings Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• If the Exterior Overcut on Drops cuts Too long or Too short.

The Exterior Overcut controls where the Blade Retracts the BladeRetracts from the Matboard (not the Fallout) on the Exterior cutcuts of Openings.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.

Image AddedImage Added

See: Exterior Overcut for Drops Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The Exterior Overcut controls where the Blade Retracts the BladeRetracts from the Matboard (not the Fallout) on the Exterior cutcuts of Openings.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.

Image AddedImage Added

See: Exterior Overcut for the Outside Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

The V-Groove Exterior Overcut Overcut controls where the Blade Retracts the Blade Retracts from the Matboard(not the Fallout)on the Exterior cuts of the Outside Cut of the Non-Oval V-Groove.

The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configurations screen and the Map illustration.Cut is where the Blade Plunges or Retracts from the Matboard (not the Fallout).  

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decreasethe Exterior Overcut.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut.

The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.

Image AddedImage Added

See: V-Groove Exterior Overcut Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Exterior If the Overcut on Creases is Too long or Too short.

The Exterior Overcut controls where the Blade Retracts the cartridgeRetracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

The Overcut field is marked with a Red Arrow on the Configuration screen and the Mapillustration.

Image AddedImage Added

See: Overcut for Creases Configurations

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.