Page Comparison

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Exterior Overcut on Openings cuts Too long or Too short.

• Exterior Overcut cuts Too Long:

  • Decrease the Exterior Overcut.

• Exterior Overcut cuts Too Short:

  • Increase the Exterior Overcut.

• See Exterior Overcut on Openings for additional information.

• Exterior Overcut cuts Too Long:

  • Decrease the Exterior Overcut.

• Exterior Overcut cuts Too Short:

  • Increase the Exterior Overcut.

• See Exterior Overcut on Drops for additional information.

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

• Exterior Overcut for Outsides cuts Too long or Too short.

• Exterior Overcut cuts Too Long:

  • Decrease the Exterior Overcut.

• Exterior Overcut cuts Too Short:

  • Increase the Exterior Overcut.

  See 

  • Exterior Overcut

  on the Outside for additional information

  • .

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior OvercutArrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

• Exterior Overcut for V-Grooves cuts Too long or Too short.

• Exterior Overcut on the Outside Cut of the V-Groove cuts Too Long:

  • Decrease the Exterior Overcut.

• Exterior Overcut on the Outside Cut of the V-Groove cuts Too Short:

  • Increase the Exterior Overcut.

  See Exterior Overcut on V-Grooves for additional information

  • Exterior Overcut.

The V-Groove Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout)on the Exterior cuts of the Outside Cut of the V-Groove.

The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configurations screen and the Map illustration.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decrease the Exterior Overcut.If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior OvercutShort, Increase the Exterior Overcut.

• Exterior Overcut on Creases is Too long or Too short.

• Exterior Overcut cuts Too Long:

  • Decrease the Exterior Overcut.

• Exterior Overcut cuts Too Short:

  • Increase the Exterior Overcut.

  See Exterior Overcut on Creases for additional information

  • Exterior Overcut.

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.