Cartridges Involved |
|---|
This Configuration element involves the following Cartridges. | Info |
|---|
Note: Not all cartridges are available for all CMC models. |
| 
Image RemovedEditing the Rotation on Outsides |
|---|
| Expand |
|---|
| A Swoopin a Non-Oval Opening is where the corners Curve Inward toward the opening. The Rotation controls for Swoops and Flares in Non-Oval Openings. If the Non-Oval Opening has a Swoop, Increase the Rotation. |
| Expand |
|---|
| A Flare in aNon-OvalOpening is where the corners Curve Away from the opening. The Rotation controls for Swoops and Flares in Non-Oval Openings. If the Non-Oval Opening cuts with a Flare, Decrease the Rotation. |
Selecting the Rotation in the Configurations | Expand |
|---|
| title | When Cutting from the Front |
|---|
| Select Current Bevel Type-Front of Mat when cutting from the front of the mat. *The different Opening Bevel Types, including whether it is cutting from the Front or Back, controls the cut direction of the Head, and determines whether the cut is a Backup or an Overcut. |
| Expand |
|---|
| title | How to Adjust the Rotation |
|---|
| When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times. Click OK and do another test cut. Continue making adjustments until the desired outcome is achieved. |
| |
Outside has a Swoop |
|---|
Problem:| Panel |
|---|
| panelIconId | atlassian-note |
|---|
| panelIcon | :note: |
|---|
| bgColor | #B3F5FF |
|---|
| |
Resolution:| Panel |
|---|
| panelIconId | atlassian-note |
|---|
| panelIcon | :note: |
|---|
| bgColor | #B3F5FF |
|---|
| |
| Expand |
|---|
| A Swoopin a Non-Oval Opening is where the corners Curve Inward toward the opening. The Rotation controls for Swoops and Flares in Non-Oval Openings. If the Non-Oval Opening has a Swoop, Increase the Rotation. |
| |
Outside has a Flare |
|---|
Problem:| Panel |
|---|
| panelIconId | atlassian-note |
|---|
| panelIcon | :note: |
|---|
| bgColor | #B3F5FF |
|---|
| |
Resolution:| Panel |
|---|
| panelIconId | atlassian-note |
|---|
| panelIcon | :note: |
|---|
| bgColor | #B3F5FF |
|---|
| |
| Expand |
|---|
| A Flare in aNon-OvalOpening is where the corners Curve Away from the opening. The Rotation controls for Swoops and Flares in Non-Oval Openings. If the Non-Oval Opening cuts with a Flare, Decrease the Rotation. |
| |
Twisted Corner |
|---|
Problem:| Panel |
|---|
| panelIconId | atlassian-note |
|---|
| panelIcon | :note: |
|---|
| bgColor | #B3F5FF |
|---|
| A Twisted Corner is when the blade turns before retracting from the matboard, which tears the matboard and twists the corner. This is especially visible from the back of the mat.
|
Resolution:| Panel |
|---|
| panelIconId | atlassian-note |
|---|
| panelIcon | :note: |
|---|
| bgColor | #B3F5FF |
|---|
| Check to make sure the Rotation hasn't been set to a high number. Twisted corners can also be a symptom of oil/water in the Air Valve, or an issue with the Head. Check the Air Regulator for excess water. Use the Clean the Foot Block procedure for cleaning the foot block.
|
| |