Versions Compared

Old Version 53

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 54

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Info

Note: Not all cartridges are available for all CMC models.

Editing the Rotation on Outsides

Expand
titleRotation Definition

The Rotation controls for Swoops and Flares in Non-Oval Objects.

Expand
titleSwoop Definition

A Swoopin a Non-Oval Opening is where the corners Curve Inward toward the opening.

The Rotation controls for Swoops and Flares in Non-Oval Openings.

If the Non-Oval Opening has a Swoop, Increase the Rotation.

Expand
titleFlare Definition

A Flare in aNon-OvalOpening is where the corners Curve Away from the opening.

The Rotation controls for Swoops and Flares in Non-Oval Openings.

If the Non-Oval Opening cuts with a Flare, Decrease the Rotation.

Selecting the Rotation in the Configurations

Expand
titleWhen Cutting from the Front

Select Current Bevel Type-Front of Mat when cutting from the front of the mat.

*The different Opening Bevel Types, including whether it is cutting from the Front or Back, controls the cut direction of the Head, and determines whether the cut is a Backup or an Overcut.

Expand
titleHow to Adjust the Rotation

When adjusting Configurations, click the Plus (Increase) or Minus (Decrease) button on the desired field about five times.

Click OK and do another test cut.

Continue making adjustments until the desired outcome is achieved.

Outside has a Swoop

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Non-Oval Outside has a Swoop.

Resolution:

Non-Oval Outside has a Swoop:
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF
Expand
titleSwoop Definition

A Swoopin a Non-Oval Opening is where the corners Curve Inward toward the opening.

The Rotation controls for Swoops and Flares in Non-Oval Openings.

If the Non-Oval Opening has a Swoop, Increase the Rotation.

Outside has a Flare

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Non-Oval Outside has a Flare.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Non-Oval Outside has a Flare, Decrease the Rotation.

Expand
titleFlare Definition

A Flare in aNon-OvalOpening is where the corners Curve Away from the opening.

The Rotation controls for Swoops and Flares in Non-Oval Openings.

If the Non-Oval Opening cuts with a Flare, Decrease the Rotation.

Twisted Corner

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • A Twisted Corner is when the blade turns before retracting from the matboard, which tears the matboard and twists the corner.

  • This is especially visible from the back of the mat.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  1. Check to make sure the Rotation hasn't been set to a high number. 

  2. Twisted corners can also be a symptom of oil/water in the Air Valve, or an issue with the Head.

  3. Check the Air Regulator for excess water.

  4. Use the Clean the Foot Block procedure for cleaning the foot block.