Versions Compared

Old Version 30

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 31

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Info

Note: Not all cartridges are available for all CMC models.

Exterior Overcut Definition

Adjusting the Exterior Overcut

Tip

  • To adjust, click Plus/Minus on the desired field about five times.

  • Click OK and do another test cut.

  • Continue making adjustments until the desired outcome is achieved.

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

Select the Bevel Type for the Exterior Overcut to be Edited:

Exterior Overcut on Openings

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Exterior Overcut on Openings cuts Too long or Too short.

Tip

  • Normal Bevel

  • Reverse Bevel

  • Normal Bevel-Front of Mat

  • Reverse Bevel-Front of Mat

  • Openings cuts Too long or Too short.

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

Exterior Overcut on Drops 

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Exterior Overcut on Drops cuts Too long or Too short.

Tip

  • Normal Drop

  • Reverse Drop

  • Normal Drop-Front of Mat

  • Reverse Drop-Front of Mat

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

Exterior Overcut on the Outside

Problem:

tip
Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Exterior Overcut for Outsides cuts Too long or Too short.

  • Outside

  • Outside-Front of Mat

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.

Exterior Overcut on V-Grooves 

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Exterior Overcut for V-Grooves cuts Too long or Too short.

Tip

  • V-Grooves

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Exterior Overcut on the Outside Cut of the V-Groove cuts Too Long:

  • Exterior Overcut on the Outside Cut of the V-Groove cuts Too Short:

Expand
titleV-Groove Exterior Overcut Definition

The V-Groove Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout)on the Exterior cuts of the Outside Cut of the V-Groove.

The V-Groove Exterior Overcut field is marked with a Red Arrow on the Configurations screen and the Map illustration.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut on the Outside Cut of the V-Groove is cut Too Short, Increase the Exterior Overcut.

Exterior Overcut on Creases

Problem:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

  • Exterior Overcut on Creases is Too long or Too short.

Tip

  • Crease

Resolution:

Panel
panelIconIdatlassian-note
panelIcon:note:
bgColor#B3F5FF

Expand
titleExterior Overcut Definition

The Exterior Overcut controls where the Blade Retracts from the Matboard (not the Fallout) on the Exterior cut.

The Exterior Overcut field is marked with a Red Arrow on the Configuration screen and the Map illustration.

If the Exterior Overcut is cut Too Long, Decrease the Exterior Overcut.

If the Exterior Overcut is cut Too Short, Increase the Exterior Overcut.