Versions Compared

Old Version 17

changes.mady.by.user dani.simmonds

Saved on

compared with

New Version 18

changes.mady.by.user dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cut the Outside On  

Info

Use the Cut the Outside toggle to select Cutting or Not Cutting the Outside of the mat for the CMC Z1, Z (9000z), 9000, and 8000.

  • Click the Cut Outside toggle On to cut the outside of the mat.

  • The outside of the mat will now cut. 

Info

Note: You can also select Options > Cut Outside.

Image RemovedImage Added

Cut the Outside Off

  • Click the Cut Outside toggle Off to not cut the outside of the mat.

  • The outside of the mat will not be cut.

Image RemovedImage Added

Set Advanced Options: Enable Outside Cut

Image Modified

Defaults: Set the Default for Cutting the Outside 

Expand
titleDefault Settings for Cutting the Outside

The default setting for Cutting the Outside can be set in the Admin > Editor section for the CMC Z1, Z (9000z), 9000 and 8000.

Image Modified

Defaults: Set the Default for 90 Degree Outside Cut

Expand
titleDefault Settings for Cutting the Outside with the 90 Degree Cartridge

The default setting for 90 Outside Cuts can be set in the Admin > Cutting section for the CMC Z1, Z (9000z) and 9000.

Note that the CMC 8000 does support cutting with the 90 Degree Cartridge.

Image Modified

Enable Auto Clamp Offset

Info

  • Select Enable Auto Clamp Offset checkbox to move the design up and over on the matboard to avoid the clamp area on the CMC Z1 and Z (9000z), similar to the Rail Dodge below.

  • Click on the design to select it.

  • Check the Enable Auto Clamp Offset checkbox.  

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.

  • This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

Expand
titleEnable Auto Clamp Definition

The Auto Clamp Offset function moves the design up and over on the matboard to avoid the Clamp area on the CMC Z1 and Z (9000z) to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

Image Modified

Disable Auto Clamp Offset

Info

  • Disabling the Auto Clamp Offset will cut the design normally without being offset into the mat on the CMC Z1 and Z (9000z).

  • Click on the design to select it.

  • Uncheck the Enable Auto Clamp Offset checkbox.

  • The design will no longer be offset on the CMC Z1 and Z (9000z) and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

  • This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

Expand
titleEnable Auto Clamp Definition

The Auto Clamp Offset function moves the design up and over on the matboard to avoid the Clamp area on the CMC Z1 and Z (9000z) to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

Image Modified

Defaults: Set the Default for the Enable Auto Clamp Offset

Expand
titleSet the Default to Enable Auto Clamp Offset

The default setting and offset value for the Enable Auto Clamp Offset for the CMC Z1 and Z (9000z) can be set in the Admin > Cutting section.

Image Modified

Enable Rail Dodge

Info

  • The Enable Rail Dodge will move the design up and over on the matboard to avoid the clamping area on the CMC 9000 and 8000.

  • Click on the design to select it.

  • Check the Enable Rail Dodge checkbox to use a Rail Dodge on CMC 9000 and 8000. 

  • A Rail Dodge is a small piece of matboard or other material used to position the pre-cut matboard up into the cutting area when using borders less than 1.5" and not cutting the outside.

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.

Info

Note: The outside cut is shown here merely for visual reference of where the pre-cut matboard will be positioned on the board. This feature can also be used to move the design to avoid flaws in the matboard.

Expand
titleRail Dodge Definition

The Rail Dodge function moves the design up and over on the matboard to avoid the Clamp area on the CMC 9000 and 8000 to overcome the Border Limitation of 1.5”/3.8cm on the Cut Preview.

Image Modified

Disable Rail Dodge

Info

  • Disabling the Rail Dodge will now cut the designs normally without being offset up and over on the mat.

  • Click on the design to select it.

  • Uncheck the Enable Rail Dodge checkbox.

  • The design will no longer be offset on the CMC 9000 and 8000 and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

  • This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

Expand
titleRail Dodge Definition

The Rail Dodge function moves the design up and over on the matboard to avoid the Clamp area on the CMC 9000 and 8000 to overcome the Border Limitation of 1.5”/3.8cm on the Cut Preview.

Image Modified

Defaults: Set the Default for the Rail Dodge

Expand
titleDefault Setting for Rail Dodge

The default setting and offset value for the Rail Dodge can be set in the Admin > Cutting section.

Image Modified

See Also: Edit Menu: Cut Outside

Info

  • Optionally, you can use the Edit menu to cut the outside of the design.

  • Click on the design to select it.

  • Click Edit > Cut Outside to cut the outside of the mat.

  • It will now cut the outside of the mat.

Image Modified