Versions Compared

Version Old Version 25 New Version 26
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Location Tab

Info

  • The Location tab allows the user to specify the desired position on the board to cut the current design. 

  • This is helpful when calibrating, avoiding flaws in the matboard, reusing scraps, etc.

X and Y Origin

Info

  • Use the X Origin (Horizontal) and Y Origin (Vertical) fields to move the design to the specific location to cut.

  • Click on the design to select it.

  • Enter a new X or Y Origin value and tab out of the field.

  • It will move the lower left corner point of the design to the new X/Y Position on the Cut Preview Screen.

  • Previous Cuts are displayed in Faded Grey to help the user position the current design on the screen.

  • To clear the Previous Cuts from the screen, click Clear Cut History.

Expand
titleX Position Definition

The X Position field is used to manually set the Horizontal position of the selected object in Designer and the Cut Preview. 

Expand
titleY Position Definition

The Y Position field is used to manually set the Vertical position of the selected object in Designer and the Cut Preview. 

Expand
titlePrevious Cuts Definition

The Previous Cuts are displayed on the Cut Preview as Faded Gray outlines.

These allow you to position the next cut beside a previous cut when cutting several designs from the same mat, such as when Calibrating the CMC.

This can be turned on/off in the Options menu, and the previous cuts can be cleared from the screen from the Clear Cut History button.

...

Enable Auto Clamp Offset

Info

  • Select Enable Auto Clamp Offset checkbox to move the design up and over on the matboard to avoid the Clamp area on the CMC Z1 and Z (9000z), similar to the Enable Rail Dodge below.

  • Click on the design to select it.

  • Check the Enable Auto Clamp Offset checkbox.  

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.

  • This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

Expand
titleEnable Auto Clamp Offset Definition

The Auto Clamp Offset function moves the design up and over on the matboard to avoid the Clamp area on the CMC Z1 and Z (9000z) to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

Disable Auto Clamp Offset

Info

  • Disabling the Auto Clamp Offset will cut the design normally without being offset into the mat on the CMC Z1 and Z (9000z).

  • Click on the design to select it.

  • Uncheck the Enable Auto Clamp Offset checkbox.

  • The design will no longer be offset on the CMC Z1 and Z (9000z) and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

  • This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

Info

Note: The outside cut is shown here merely for visual reference of where the pre-cut matboard will be positioned on the board. This feature can also be used to move the design to avoid flaws in the matboard.

Expand
titleEnable Auto Clamp Offset Definition

The Auto Clamp Offset function moves the design up and over on the matboard to avoid the Clamp area on the CMC Z1 and Z (9000z) to overcome the Border Limitation of 1.25"/3.2 cm on the Cut Preview.

...

Enable Rail Dodge

Info

  • The Enable Rail Dodge will move the design up and over on the matboard to avoid the clamping area on the CMC 9000 and 8000.

  • Click on the design to select it.

  • Check the Enable Rail Dodge checkbox to use a Rail Dodge on CMC 9000 and 8000. 

  • A Rail Dodge is a small piece of matboard or other material used to position the pre-cut matboard up into the cutting area when using borders less than 1.5" and not cutting the outside.

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y Position and it will display Dodge on the bottom of the screen.

Info

Note: The outside cut is shown here merely for visual reference of where the pre-cut matboard will be positioned on the board. This feature can also be used to move the design to avoid flaws in the matboard.

Expand
titleRail Dodge Definition

The Rail Dodge function moves the design up and over on the matboard to avoid the Clamp area on the CMC 9000 and 8000 to overcome the Border Limitation of 1.5”/3.8cm on the Cut Preview.

See Also: Fixture for Rail Dodge.  

Disable Rail Dodge

Info

  • Disabling the Rail Dodge will now cut the designs normally without being offset up and over on the mat.

Expand
titleRail Dodge Definition
The Rail Dodge function moves the design up and over on the matboard to avoid the Clamp area on the CMC 9000 and 8000 to overcome the Border Limitation of 1.5”/3

  • .

8cm on the Cut Preview.

  • Click on the design to select it.

  • Uncheck the Enable Rail Dodge checkbox.

  • The design will no longer be offset on the CMC 9000 and 8000 and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

  • This is useful when cutting the opening from a pre-cut sheet matboard and not cutting the outside.

Expand
titleRail Dodge Definition

The Rail Dodge function moves the design up and over on the matboard to avoid the Clamp area on the CMC 9000 and 8000 to overcome the Border Limitation of 1.5”/3.8cm on the Cut Preview.

Defaults: Set the Default for the Rail Dodge

Expand
titleDefault Setting for the Rail Dodge

The default setting for the Rail Dodge can be set in the Admin > Cutting section.

Move Origin Arrows

Info

  • Use the Origin Arrows to move the current design on the Cut Preview screen a full Design Width/Height distance. This allows you to cut consecutive mats when calibrating, or using up scrap mats, etc.

  • Click on the design to select it.

  • The Move Origin Arrows (Up, Down, Left or Right) moves the current design by a full design's outside Width or Height in the direction of the arrow.

  • For example, clicking the Right Arrow will move the design over the same full design width to the Right, so that it can be cut next to the previous cut that was made with this design.

Expand
titlePrevious Cuts Definition

The Previous Cuts are displayed on the Cut Preview as Faded Gray outlines.

These allow you to position the next cut beside a previous cut when cutting several designs from the same mat, such as when Calibrating the CMC.

This can be turned on/off in the Options menu, and the previous cuts can be cleared from the screen from the Clear Cut History button.

...

Clear Cut History Button

Info

  • Use the Clear Cut History button to clear the Previously Cut mats from the Cut Preview Screen.

  • The Previous Cuts on the screen are drawn out in Faded Gray outlines.

  • Click the Clear Cut History button.

  • The Previous Cuts on the screen are erased.

  • This is helpful when the previous cuts are a distraction for the current session, or you no longer need them as a reference when moving the position of the current design to cut.

Expand
titlePrevious Cuts Definition

The Previous Cuts are displayed on the Cut Preview as Faded Gray outlines.

These allow you to position the next cut beside a previous cut when cutting several designs from the same mat, such as when Calibrating the CMC.

This can be turned on/off in the Options menu, and the previous cuts can be cleared from the screen from the Clear Cut History button.

...