Versions Compared

Version Old Version 22 New Version 23
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Location Tab

Info

  • The Location tab allows the user to specify the desired position on the board to cut the current design.

 This

  •  

  • This is helpful when calibrating, avoiding flaws in the matboard, reusing scraps, etc.

X and Y Origin

Info

  • Use the X Origin (Horizontal) and Y Origin (Vertical) fields to specify the location to cut the current mat.

Expand
titleX Position Definition

The X Position fieldField is used to manually set the horizontal Horizontal position of the selected template object. 

Expand
titleY Position Definition

The Y Position fieldField is used to manually set the vertical Vertical position of the selected template object. 

  • Click on the design to select it.

  • Enter a new X or Y Origin value and tab out of the field.

  • It will move the lower left corner of the current design to the new X/Y position Position on the Cut Preview Screen based on the lower left corner of the design.

  • Previous cuts are displayed in grey Grey to help the user position the current design on the screen.

  • To clear the previous cuts from the screen, see Clear Cut History.

See Also: Matboard Size

  • Enter the desired matboard sheet size Matboard Sheet Size on the Setup Tab on the Sheet Size field.

  • The software will use the matboard size as the maximum limitation when tiling mats and when moving mats with the Location Tab.

...

Enable Auto Clamp Offset

Info

  • Select Enable Auto Clamp Offset checkbox to move the design up and over on the matboard to avoid the clamp area on the CMC Z1 and Z (9000z), similar to the Enable Rail Dodge below.

Expand
titleEnable Auto Clamp Offset Definition

The Auto Clamp Offset function moves the design up and over on the matboard to avoid the clamp Clamp area on the CMC Z1 and Z (9000z) to overcome the border limitation Border Limitation of 1.25"/3.2 cm when not cutting the outsidecm on the Cut Preview.

  • Click on the design to select it.

  • Check the Enable Auto Clamp Offset checkbox.  

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y position and it will display Dodge on the bottom of the screen.

  • This feature is also turned on by selecting Full from the Outside Cut Options dropdown control.

Disable Auto Clamp Offset

Info

  • Disabling the Auto Clamp Offset will cut the design normally without being offset into the mat on the CMC Z1 and Z (9000z).

Expand
titleEnable Auto Clamp Offset Definition

The Auto Clamp Offset function moves the design up and over on the matboard to avoid the clamp Clamp area on the CMC Z1 and Z (9000z) to overcome the border limitation Border Limitation of 1.25"/3.2 cm when not cutting the outsidecm on the Cut Preview.

  • Click on the design to select it.

  • Uncheck the Enable Auto Clamp Offset checkbox.

  • The design will no longer be offset on the CMC Z1 and Z (9000z) and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

...

Enable Rail Dodge

Info

  • The Enable Rail Dodge will move the design up and over on the matboard to avoid the clamping area on the CMC 9000 and 8000.

Expand
titleRail Dodge Definition

A The Rail Dodge Dodge function moves the design up and over on the matboard to avoid the clamp Clamp area on the CMC 9000 and 8000 to overcome the border limitation Border Limitation of 1.5”/3.8cm when not cutting the outside on the Cut Preview.

  • Click on the design to select it.

  • Check the Enable Rail Dodge checkbox to use a Rail Dodge on CMC 9000 and 8000. 

  • A Rail Dodge is a small piece of matboard or other material used to position the pre-cut matboard up into the cutting area when using borders less than 1.5" and not cutting the outside.

  • Enter the distance to move the design in the X Origin field; the Y Origin field uses the same numerical value. 

  • It will move the lower left corner of the design to the new X/Y position and it will display Dodge on the bottom of the screen.

Info

Note: The outside cut is shown here merely for visual reference of where the pre-cut matboard will be positioned on the board. This feature can also be used to move the design to avoid flaws in the matboard.

See Also: Fixture for Rail Dodge.  

Disable Rail Dodge

Info

  • Disabling the Rail Dodge will now cut the designs normally without being offset up and over on the mat.

Expand
titleRail Dodge Definition

A The Rail Dodge Dodge function moves the design up and over on the matboard to avoid the clamp Clamp area on the CMC 9000 and 8000 to overcome the border limitation Border Limitation of 1.5”/3.8cm when not cutting the outside on the Cut Preview.

  • Click on the design to select it.

  • Uncheck the Enable Rail Dodge checkbox.

  • The design will no longer be offset on the CMC 9000 and 8000 and will cut the design normally unless values have been entered in the X Origin and Y Origin fields as described above.

...

Move Origin Arrows

Info

  • Use the origin arrows Origin Arrows to move the current design on the cut preview screen by the same width/height distance of the design to where you would it to cut. This allows you to cut consecutive mats when calibrating, or using up scrap mats, etc.

  • Click on the design to select it.

  • The Move Origin Arrows (Up, Down, Left or Right) moves the current design by a full design's width or height in the direction of the arrow.

  • The design's width or height also includes the outside dimension. 

  • For example, clicking the right arrow will move the design over the same full design width to the right, so that it can be cut next to the previous cut that was made with this design.

...

See Also: Interacting Directly With the Designs on the Cut Preview Screen

Info