Versions Compared

Version Old Version 6 New Version 7
Changes made by

dani.simmonds

dani.simmonds

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Cartridges Involved

This Configuration element involves the following Cartridges.

Note: Not all cartridges are available for all CMC models.

The Other Cartridge Adjustments Involve These Cartridges

Other Cartridge Adjustments

The Other Cartridge Adjustments section contains additional configuration fields for V-Grooves and for the non-blade cartridges.

Select the Cartridge Adjustment to be Edited:

Width Adjustment (V-Groove)

Select this topic to see information on editing the 

Problem:

  • The V-Groove

 width if it

  • width is

cutting too wide or too narrow

  • cut too large/too small.

Resolution:

Adjust the V-Groove Width Adjustment.

Outside Rotation (V-Groove) 

Select this topic to see information on editing for a Swoop or Flare on the Outside cut of

Problem:

  • The Outside V-Groove cuts with a Swoop/Flare.

Resolution:

Adjust the V-Groove Outside Rotation on a Non-Oval V-Groove.

Inside Rotation (V-Groove) 

Select this topic to see information on editing for a Swoop or Flare on the Inside cut of

Problem:

  • The Inside V-Groove cuts with a Swoop/Flare.

Resolution:

Adjust the V-Groove Inside Rotation on a Non-Oval V-Groove.

Outside Oval Rotation (V-Groove)  

Select this topic to see information on editing for a Bump or Feather

Problem:

  • The Outside Oval V-Groove cuts with a Feather/Bump.

Resolution:

Adjust the V-Groove Outside Oval Rotation on the Outside cut of an Oval V-Groove.

Inside Oval Rotation (V-Groove)  

Select this topic to see information on editing for a Bump or Feather

Problem:

  • The Inside Oval V-Groove cuts with a Feather/Bump.

Resolution:

Adjust the V-Groove Inside Oval Rotation on the Inside cut of an Oval V-Groove.

Horizontal Adjustment (Tool Specific) 

Select this topic to see information on editing the Horizontal placement for

Problem:

  • The Tool Object is applied in the wrong place Horizontally.

Resolution:

Edit the Horizontal Adjustment for the Deboss, Pen or Vinyl tool.

Vertical Adjustment (Tool Specific) 

Select this topic to see information on editing the Vertical placement for

Problem:

  • The Tool Object is applied in the wrong place Vertically.

Problem:

Edit the Vertical Adjustment for the Deboss, Pen or Vinyl tool.

Depth Setting (Tool Specific) 

Select this topic to see information on selecting

Problem:

  • The Tool is applied at the wrong blade depth.

Resolution:

Adjust the optimum Blade Depth for the Deboss, Pen or Vinyl tool.

Corner Pause (ms) (Tool Specific)  

Select this topic to see information on editing the

Problem:

  • The Tool is tearing the matboard.

Resolution:

Adjust the amount of time to Pause in the corners, in milliseconds, when applying the Deboss, Pen or Vinyl tool.

Overshoot (Tool Specific) 

Select this topic to see information on editing how much to 

Problem:

  • The Tool line is applied too long/too short.

Resolution:

Adjust the length of the Overshoot past the end of the segment for Deboss, Pen or Vinyl tool. This is similar to an Overcut.

Plunge (Tool Specific) 

Problem:

  • Select

this topic to see information on editing whether

  • whether to Plunge/Unplunge the Tool between segments.

Resolution:

Adjust whether to Plunge or Unplunge between segments of an object when doing a Deboss, Pen or Vinyl object.

Install Pen  

Select this topic to see information on using

Problem:

  • How to calibrate the Pen Tool.

Resolution:

Use the Install Pen utility to calibrate the system for different pens.