...
...
| View file | ||
|---|---|---|
|
Select Layer to Cut | |
|---|---|
On the cut preview screen under layer, click on the desired layer. Current layer indicator is highlighted in red. Current layer on mat preview is displayed in red. To cut a different layer, click on the desired layer. Alternatively, click on the +/- next to layer to select the desired layer. After cutting, the software automatically rolls over to the next layer to cut unless Continuous Layer has been checked. |  |
Put Matboard on the CMC |
|---|
Make sure you have two layers of disposable matboard of adequate size underneath the mat to be cut. A layer may need to be temporarily removed for thicker matboard. |
Have two layers of adequate size of disposable matboard under mat to be cut. A layer can be temporarily removed for thicker matboard. |
...
Variable Pressure Optimization (VPO) Feature - Adjusting the Air Pressure for Typical Matboard | |
|---|---|
Note: Decreasing the air pressure will decrease the blade depth. The head air regulator is located on the left side of the head, and controls the air pressure of the head as it is cutting. The air pressure is applied when the head is cutting. The minimum air pressure should be 35 psi, otherwise the blade may not cut through the matboard. The maximum air pressure should be around 60 psi to avoid crushing the matboard. The MatDesigner software will prompt for a head pressure change only if the current mat is a different setting than the previously cut mat. All designs come to the Cut Preview with Dense unchecked on the Blade Depth Screen. Returning to the editor and going to the Cut Preview resets the layers to typical matboard with Dense unchecked. |   |
Click Cut and Align the Head if requested. The Head plunges at the home position and applies the current pressure and displays a prompt to adjust the head pressure to the low setting. |  |
Pull out the air regulator pressure knob by pulling it to the left. |   |
Turn the air regulator pressure knob counter-clockwise until the marker on the gauge is at the low setting. |   |
Make sure the gauge does not go below 35 psi. |   |
Push the air regulator pressure knob back in by pushing it to the right. Click OK to cut the mat with this setting. | |
Variable Pressure Optimization (VPO) Feature - Cutting an Extra Dense Layer with the 90° Cartridge | |
|---|---|
This setting is only for the 90° Cartridge and will not take affect if another cartridge is selected. This setting will allow the 90° Cartridge to cut at a slower pace. Select the desired layer on the Cut Preview. Click the Blade Depth button to open the Blade Depth Screen. |  |
Click the checkbox for Dense (and change the Blade Depth to the appropriate setting for this matboard. Click the checkbox for Extra Dense Material. Adjust the slidebar to the percentage of cutting speed. For instance, 50% is 50% of the standard cutting speed. |   |
Click Ok. The Cut Preview displays the dense layer with an asterisk with pound sign and indicates that this layer is extra dense. |  |
Click Cut the cut the mat and Align the Head if requested. A prompt to adjust the head pressure to the high setting displays. |   |
Pull out the air regulator pressure knob by pulling it to the left. |  |
Turn the air regulator pressure knob clockwise until the marker on the gauge is at the high setting. |   |
Make sure the gauge does not go above 60 psi. |  |
Push the air regulator pressure knob back in by pushing it to the right. Click OK to cut the mat with this setting. | |
Cutting 8-ply |
|---|
NOTE: If you do not have a license for the 45°+ cartridge, this feature will not be available. Select 8-ply matboard from the matboard library, or change the blade depth dial to 8-ply setting. Click blade depth button on the cut preview and select the matching blade depth setting in the software. Click Ok. Click cut. Insert the 45°+ cut cartridge when prompted. See Measuring Blade Depth for specific instructions. |
Cutting V-Grooves | |
|---|---|
V-Grooves and openings on that layer will automatically cut from the front. There is a separate configuration for these openings (i.e., Normal Bevel - Front of Mat) because they are cut from the front of the mat. Place mat face up on CMC (facing you). Make sure matboard nestles tightly into horizontal and vertical clamps of the CMC. |   |
If the current layer uses a different cartridge or is a different thickness than the last layer cut, the user is prompted to change the cartridge and the blade depth to V-Groove depth. Change the cartridge/blade depth as prompted and click Ok. The V-Groove cuts. A prompt displays to change blade depth knob to matboard setting. Change the blade depth knob to the requested setting. Click Ok. The openings on the same layer as the V-Groove will now cut. Have one layer of adequate size of disposable matboard under mat to be cut on the CMC 8500e; two layers for the CMC 8000. A layer can be temporarily removed for thicker matboard. |   |
Align the Head | |
|---|---|
Never pull/push on the drive shaft to move the gantry. Use the gantry arm. | |
If motors to the CMC have been idle (i.e., head moves easily up and down with no power to motors), or a cut has been aborted, the head has to be aligned for the next cut. Rotate the foot block into the 12 O’Clock position, with the blade cartridge on top of the head. Holding it about an inch above the bottom rail, slide the gantry and the head assembly to the left edge of the CMC until it stops. Then slide the head down until the foot block rests against the head alignment stop. |   |
Click on the align screen. |   |
The head will align to the home position. |   |
If the current layer uses a different blade cartridge or is a different thickness than the last layer cut, the user will be prompted to change the blade cartridge and/or the blade depth before it cuts. If the current layer uses the same blade cartridge and the same thickness as the last layer cut, the CMC will begin to cut without further prompt. |   |
Insert the requested blade cartridge and turn the blade depth dial to the requested depth and click Ok on the prompt. The CMC will begin to cut. After cutting has completed or when plunge count is selected, head rotates foot block in the aligned position for access to blade cartridge. Do NOT turn the foot block unless prompted to align the head. |   |
Cutting in Progress | |
|---|---|
As the CMC cuts, Press Spacebar to PAUSE and Press Any Other Key to ABORT screen interchange. |   |
Cut Next Layer | |
|---|---|
After cutting, the software automatically rolls over to the next layer to cut on a multi-layer mat. If continuous layer is selected, the software remains on the current layer without rolling over. NOTE: If blade depth software setting for the next layer is a different depth than the previous layer, a prompt to change blade depth dial displays. See Blade Depth Adjustment - CMC Models 8000/8500e for more information. |   |
Pause the Cut Manually | |
|---|---|
Hit spacebar to pause the cut. The pause screen opens. Pause temporarily suspends the cutting process, which can then be restarted where it left off. Click Continue to resume cutting current project. OR Click Blade to change the blade. The head rotates so user can change the blade. Hit CTRL+S after changing blade to return to cutting. OR Click Abort or hit any other key on keyboard to abort the cut. |   |
Restarting the Cut | |
|---|---|
Paused with Spacebar Click Continue to resume cutting the current project. OR If user clicked Blade to change the blade, hit CTRL+S after changing blade to restart cutting. OR Click Abort or hit any other key on the keyboard to Abort the cut. | |
Paused for Plunge Count Blade Change Select Plunge Count to prompt for a blade change after a set number of plunges. CMC will pause cutting and prompt user to change the blade. |  |
Change the blade and hit CTRL+S or click on the screen to continue cutting. Number of plunges is managed in the configurations screen, and will be described there. Unselect Plunge Count to manually manage blade changes. |   |